Introduction

This section describes all types of input and output signals available on iam cameras, including their characteristics and when necessary including connection examples. Location and pinouts of the connectors carrying the signals is documented in Section “Dimensions” and Section “Connector and cable description”

Power supply

DC power input

iam is designed for a power supply input range of 24 V ±10%. The power consumption depends on the utilisation of the main system parts: Image sensor, FPGA, ARM cores. The power consumption is typically less than 13 W. A suitable power supply for iam is available from NET.

For designing a custom power supply see information about the power input connector in Connector and cable description.

Power over Ethernet (PoE)

Be aware in case of using a prototype camera:

If the camera serial number has an X or Z in the 9th digit (e.g. 14A2GEBAX2042013) Power over Ethernet is not supported even though the camera will be detected as a PoE device by a PoE injector!
See also Known Issues - Prototype Cameras .

iam can be also powered using the Power over Ethernet option. The cameras are compatible with the Power over Ethernet standard, versions IEEE 802.3af and 802.3at. They should be used with PoE switches (“endspans”) or power injectors (“midspans”) complying with the IEEE 802.3af/IEEE 802.3at specifications.

The iam models are classified in the power level class 0 or class 3. The power consumption with PoE is slightly higher than consumption with a “regular” power supply. When connecting multiple iam cameras to a single PoE switch, verify how much total power the switch can provide and how it handles cases when the limit is exceeded.

Both PoE modes (A and B) are supported by the camera.

Beware of using PoE cameras with 100Mbit Ethernet cables, where the “spare” wire pairs might be omitted. With such cable, the power wouldn't be delivered when using Mode B compatible power sourcing equipment.

Unable to render {include} The included page could not be found.

Connector and cable description - Case Code A

Connectors

ETH 1: RJ-45
IO: TFM-107-02-L-DH

Ethernet connector

iam is equipped with a standard Ethernet connector, 8P8C modular plug, often also referred to RJ-45.

I/O Connector

14-pin DLP (dual-inline-pin) connector for digital I/O and power input. An adapter cable is available (see Section “Accessories”).

Connector Pinout TFM-107-02-L-DH.pdf	Mates Pinnout SFSD-07-XXX-G-XX.XX-SR
view manufactor information (external link)

Connector and cable description - Case Code A

Connectors

ETH 1: M12-X PHÖNIX 1404741
SACC-DSI-FSX-8CON-PG9-L180 SCO
IO: M12-17P PHÖNIX 1437119
SACC-DSI-MS-17CON-M12 SCO SH
ETH 2: M16-X BINDER
99 4174 90 08 M16-X, 8P, schirmbar, THR, IP67

Ethernet connector

iamIP67 is equipped with one M12-X and one M16-X Ethernet connector.

M12-X - cable connector (matching type)

standard Gigabit Ethernet Connector diverse Vendors, e. g.

M12-X Male cable connector, Contacts: 8, 5.5-9.0 mm, shieldable, cutting clamp, IP67, Binder 99 3787 810 08

M16-X - cable connector (matching type)

M16-X Male cable connector, Contacts: 8, 5.5-9.0 mm, shieldable, cutting clamp, IP67, Binder 99 4171 00 08

I/O Connector

17-pin male M12 connector for digital i/o (optocoupler and TTL inputs/outputs) and power input.

An adapter cable is available (see Section “Cable Assembly”), with D-sub 25-pin female interface connector.

Cable connector: PHÖNIX M12-17P No. 1559644

Cable connector: diverse Vendors, e. g.
PHÖNIX SUBCON No. 2761619

Pinout

Cable Assembly

Case Code A:

This cable is fully shielded.

Case Code C:

Interface Break Out Boards

Interface Break Out Boards

Pinout

CBB1A R2 Break out Board

incl. DIN rail mount

075IOAD - Trigger, Strobe and IO Test Board

Trigger, Strobe and IO Test Board. Can be used to plug two iam cameras crossed together (OUT → IN , IN ← OUT).

CAM1: Primary Camera Connector

Can be fastened on backside of camera using 2x M2x6 srews (Bottom Side Connector J2) or by using discrete wire assembly from samtec SFSD-07-28-G-XX.XX-DR-NUS plugged into topside connecotr J1.

CAM2: Secondary Camera Connector

Secound iam camera can be connected crossed (OUT1 → IN2 , IN1 ← OUT2) by using discrete wire assembly from samtec SFSD-07-28-G-XX.XX-DR-NUS plugged into topside connecotr J3.

J3/J10 - AUX Power Supply

075IOAD can be powerd by 24V supply using J10 connector or J3 srew terminal. If J4 or J10 is used iam CAM1 is always powerd as well.

CAM2 can be powerd as well by jumping “CAM Power” on Terinal J13.

J11-12 - Jumper Terminals

With the Jumper Terminals J11 and J12 the camera IO-terminals can be supplied with AUX Power so additional components like LEDs and bush buttoms can be used.

See 075IOAD20_schematic.pdf for details.

Documentation

	File	Modified
Labels No labels Preview View	ZIP Archive 210916_075IOAD20.step.zip	Jan 21, 2022 by Benjamin Hoffmann (Unlicensed)
Labels No labels Preview View	PDF File 210918_075IOAD20_assembly.pdf	Jan 21, 2022 by Benjamin Hoffmann (Unlicensed)
Labels No labels Preview View	PDF File 210918_075IOAD20_schematic.pdf	Jan 21, 2022 by Benjamin Hoffmann (Unlicensed)
Labels No labels Preview View	PDF File CBB1A2TopSilk_v4_2.pdf	Apr 28, 2023 by Benjamin Hoffmann (Unlicensed)

Download All

Errata

Revision 2.0

J6

silksreen labeling is wrong

TRIG+ is IN_TRIGGER-

TRIG- is IN_TRIGGER+

should be swaped

D8, D9

silksreen labeling is wrong

D9 belongs to IN_ENC1 (OUT_GP1)

D8 belongs to IN_ENC2 (OUT_GP2)

should be swaped

🔍 References

🔗 related content

👥 contact NET

Error rendering macro 'excerpt-include' : No link could be created for 'MasterContent: Contact NET'.

Input and Output Interface

Introduction

Power supply

DC power input

Power over Ethernet (PoE)

Connector and cable description - Case Code A

Connectors

Ethernet connector

I/O Connector

Connector and cable description - Case Code A

Connectors

Ethernet connector

I/O Connector

Pinout

Cable Assembly

Case Code A:

Case Code C:

Interface Break Out Boards

Pinout

CBB1A R2 Break out Board

incl. DIN rail mount

075IOAD - Trigger, Strobe and IO Test Board

CAM1: Primary Camera Connector

CAM2: Secondary Camera Connector

J3/J10 - AUX Power Supply

J11-12 - Jumper Terminals

Documentation

Errata

Revision 2.0