Software

Release 01/2022 - 3.10 (2021.1)

Topic	Description	comment	SynView Version	Petalinux Version

Topic	Description	comment	SynView Version	Petalinux Version
SynView Explorer	User Set: save does not work, when next load is done to fast.	Issue IAM-220	SynView-1.03.014.1026	3.10
SynView Explorer	AcquisitionFrameRateTimer mode: AcquisitionFrameRate cannot be increased after increase/decrease exposure time.	Issue IAM-219	SynView-1.03.014.1026	3.10
SynView Explorer	AcquisitionFrameRateTimer mode: acquisition stops if Exposure Auto = Continuous/Once.	Issue IAM-218	SynView-1.03.014.1026	3.10
SynView Explorer	AcquisitionFrameRateTimer mode: Acquisition does not start after increasing exposure time.	Issue IAM-217	SynView-1.03.014.1026	3.10
SynView Explorer	IMX265C, IMX264C: no frame output with BGR 8 format.	Issue IAM-214	SynView-1.03.014.1026	3.10
SynView Explorer	Color Transformation: switches to OFF when aqusition is started.	Issue IAM-210	SynView-1.03.014.1026	3.10
SynView Explorer	BGR 8 format: wrong pixels can occur when Gamma,Contrast is reduced by certain brightness.	Issue IAM-209	SynView-1.03.014.1026	3.10
SynView Explorer	BalanceRatio(Selector) not shown as available in bayer mode.	Issue IAM-207	SynView-1.03.014.1026	3.10
SynView Explorer	IA2312C: list of pixelformats is not correct.	Issue IAM-206	SynView-1.03.014.1026	3.10
SynView Explorer	Trigger Modus with trigger source timer: Acquisition stops when exposure time is to high.	Issue IAM-154	SynView-1.03.014.1026	3.10
SynView Explorer	Acquisition Frame Rate Control: exposure time controls the AcquFrameRate.	Issue IAM-149	SynView-1.03.014.1026	3.10
SynView Explorer	Color Transformation: default-value for Color Transformation Value Selector=Offset 2 instead of Gain 00.	Issue IAM-148	SynView-1.03.014.1026	3.10
SynView Explorer	minimal value of field "Exposure Auto Max Time" is smaler than minimal exposure time.	Issue IAM-147	SynView-1.03.014.1026	3.10
SynView Explorer	Mono 8 is brighter as Mono10/12.	Issue IAM-142	SynView-1.03.014.1026	3.10
SynView Explorer	Trigger Modus: acquisition stops with triggerrate in relation with too high exposure time.	Issue IAM-123	SynView-1.03.014.1026	3.10
SynView Explorer	Acquisition Frame Rate: write failed message can occur .	Issue IAM-122	SynView-1.03.014.1026	3.10
SynView Explorer	User Set Default "none": data will be overwritten.	Issue IAM-121	SynView-1.03.014.1026	3.10
SynView Explorer	Digital I/O Control, Line Source "Selected Trigger" delivers no frame output.	Issue IAM-114	SynView-1.03.014.1026	3.10
SynView Explorer	Strobe Source "Static High": behaves like "Static Low".	Issue IAM-112	SynView-1.03.014.1026	3.10
SynView Explorer	ColorTransformation: if switched to off, it still affects the colors of the frame.	Issue IAM-165	SynView-1.03.014.1026	3.10
SynView Explorer	IA1503, Sensor Strobe: no Frame-output with certain Exposure Time combined with Width, Height.	Issue IAM-189	SynView-1.03.014.1026	3.10

Older Release

Release 01/2022 - 3.01 (2021.1)

Topic	Description	comment	Author	SynView Version	Petalinux Version	FPGA Version	Device Sensor Version

Topic	Description	comment	Author	SynView Version	Petalinux Version	FPGA Version	Device Sensor Version
SynView Explorer	Brightness Control - BCRM Mode / Exposure Auto Color Management -BCRM Mode / White Balance Auto → If "Once" is chosen, "Once" stays active. "OFF" is not active.	IAM-85	AKr	SynView-1.03.010.1090	2.02		34658
iAMGigEServeriAMGigEServer	Events can´t be send via GigE Server	.	MW	SynView-1.03.010.1090	2.02
SynView Explorer	Image Format: Pixel format: YUV-frame is brighter than BGR8-frame	Issue IAM-76	DP	SynView-1.03.010.1090	2.02
SynView Explorer	First frame occures to "flash"		GD	SynView-1.03.010.1090	2.02	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView IP Config Tool sv.ipconf.x64	Re-enable the GigE Vision Server autostart sometimes fails after power cycle.		GD	SynView-1.03.010.1090	2.02

Release 06/2021 - 2.02 (2020.1)

Topic	Description	comment	Author	SynView Version	Petalinux Version	FPGA Version	Device Sensor Version

Topic	Description	comment	Author	SynView Version	Petalinux Version	FPGA Version	Device Sensor Version
SynView Explorer	Brightness Control - BCRM Mode / Exposure Auto Color Management -BCRM Mode / White Balance Auto → If "Once" is chosen, "Once" stays active. "OFF" is not active.	IAM-85	AKr	SynView-1.03.010.1090	2.02		34658
iAMGigEServer	Events can´t be send via GigE Server	.	MW	SynView-1.03.010.1090	2.02
SynView Explorer	Image Format: Pixel format: YUV-frame is brighter than BGR8-frame	Issue IAM-76	DP	SynView-1.03.010.1090	2.02
SynView Explorer	First frame occures to "flash"		GD	SynView-1.03.010.1090	2.02	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView IP Config Tool sv.ipconf.x64	Re-enable the GigE Vision Server autostart sometimes fails after power cycle.		GD	SynView-1.03.010.1090	2.02

Release 10/2020 - 1.04

Topic	Description	comment	Author	SynView Version	Petalinux Version	FPGA Version	BCRM Version

Topic	Description	comment	Author	SynView Version	Petalinux Version	FPGA Version	BCRM Version
SynView Explorer	Brightness Control - BCRM Mode / Exposure Auto Color Management -BCRM Mode / White Balance Auto → If "Once" is chosen, "Once" stays active. "OFF" is not active.	Issue IAM-85	AKr	1.03.010.1060
SynView Explorer	Events can´t be send via GigE Server	.	MW	1.03.010.1061-8.10.2020
SynView Explorer	Timer/Puls generator can´t be enabled or disabled with Acquisition Start/Stop	.	MW	1.03.010.1061-8.10.2020
SynView Explorer	TriggerMode: Trigger Invert operates sensor in free-run mode		GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView Explorer	StrobeMode: Strobe assigned to wrong edge	.	GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView Explorer	StrobeMode: Strobe source: Static low remains high	.	GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView Explorer	TriggerMode: Software trigger → Strobe not available		GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView Explorer	I/O → Line5 OUT: On -> Low, OFF → High		GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView Explorer	I/O: → Line4 OUT: No function	.	GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView Explorer	Image Format: Pixel format: Format Bayer GR 10 Packed cannot be displayed Format Bayer GR 10 Packed cannot be displayed	Issue SYN-16	GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView Explorer	Image Format: Pixel format: BayerRG8-frame is brighter than BGR8-frame		GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView Explorer	Image Format: Pixel format: YUV-frame is brighter than BGR8-frame	Issue IAM-76	DP
SynView Explorer	First frame occures to "flash"		GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView Explorer	Soft image due to missing basic sensor configuration (gamma, black level)		GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300

Hardware

Topic	Description	Affects	Author

Topic

Description

Affects

Author

Power supply

Power over Ethernet is not supported even though the camera will be detected as a PoE device by a PoE injector!

If the camera serial number has an X or Z in the 9th digit (e.g. 14A2GEBAX2042013)

BH

Input and Output Interface

OUT_GP1+ is out of order and can be used in current revison. Output stays GND. This means in

SynView Explorer I/O: → Line4 OUT: No function (always one!)

If the camera serial number has an X or Y in the 9th digit (e.g. 14A2GEBAX2042013)

BH

iam

Release notes