Skip to end of metadata
Go to start of metadata
You are viewing an old version of this page. View the current version.
Compare with Current
View Page History
« Previous
Version 20
Next »
Software
Release 01/2022 - 3.10 (2021.1)
Topic | Description | comment | SynView Version | Petalinux Version |
|---|
SynView Explorer | Trigger Modus: Acquisition bleibt stehen bei Triggerrate mit zu hoher Exposure Time | Issue IAM-154 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | Acquisition Frame Rate Control: Exposure Time kontrolliert die AcquFrameRate | Issue IAM-149 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | Color Transformation: Defaultwert für Color Transformation Value Selector=Offset 2 anstatt Gain 00 | Issue IAM-148 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | Minwert von Feld "Exposure Auto Max Time" ist kleiner als minimale Exposure Time | Issue IAM-147 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | Mono 8 heller als Mono10/12 | Issue IAM-142 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | Trigger Modus: Acquisition bleibt stehen bei Triggerrate mit zu hoher Exposure Time | Issue IAM-123 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | Acquisition Frame Rate: write failed Meldung in bestimmter Situation | Issue IAM-122 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | User Set Default "none": Daten werden überschrieben | Issue IAM-121 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | Digital I/O Control, Line Source "Selected Trigger" liefert keinen Output | Issue IAM-114 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | Strobe Source "Static High": verhält sich wie Static Low | Issue IAM-112 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | ColorTransformation: wenn ausgeschalten kommt es trotzdem zur Farbänderung | Issue IAM-165 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | IA1503, Sensor Strobe: kein Output bei bestimmter Exposure Time kombiniert mit Width, Height | Issue IAM-189 | SynView-1.03.014.1026 | 3.10 |
Older Release
Release 01/2022 - 3.01 (2021.1)
Release 01/2022 - 3.01 (2021.1)
Topic | Description | comment | Author | SynView Version | Petalinux Version | FPGA Version | Device Sensor Version |
|---|
SynView Explorer | Brightness Control - BCRM Mode / Exposure Auto Color Management -BCRM Mode / White Balance Auto
→ If "Once" is chosen, "Once" stays active. "OFF" is not active. | IAM-85 | AKr | SynView-1.03.010.1090 | 2.02 | | 34658 |
iAMGigEServeriAMGigEServer | Events can´t be send via GigE Server | . | MW | SynView-1.03.010.1090 | 2.02 | | |
SynView Explorer | Image Format: Pixel format:
YUV-frame is brighter than BGR8-frame | Issue IAM-76 | DP | SynView-1.03.010.1090 | 2.02 | | |
SynView Explorer | First frame occures to "flash" | | GD | SynView-1.03.010.1090 | 2.02 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 |
SynView IP Config Tool sv.ipconf.x64 | Re-enable the GigE Vision Server autostart sometimes fails after power cycle. | | GD | SynView-1.03.010.1090 | 2.02 | | |
Release 06/2021 - 2.02 (2020.1).
Release 06/2021 - 2.02 (2020.1)
Topic | Description | comment | Author | SynView Version | Petalinux Version | FPGA Version | Device Sensor Version |
|---|
SynView Explorer | Brightness Control - BCRM Mode / Exposure Auto Color Management -BCRM Mode / White Balance Auto
→ If "Once" is chosen, "Once" stays active. "OFF" is not active. | IAM-85 | AKr | SynView-1.03.010.1090 |
2.02
|
|
34658
|
iAMGigEServer | Events can´t be send via GigE Server | . | MW | SynView-1.03.010.1090 | 2.02
|
|
|
SynView Explorer | Image Format: Pixel format:
YUV-frame is brighter than BGR8-frame | Issue IAM-76 | DP | SynView-1.03.010.1090 | 2.02 | | |
SynView Explorer | First frame occures to "flash" | | GD | SynView-1.03.010.1090 | 2.02 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 |
SynView IP Config Tool sv.ipconf.x64 | Re-enable the GigE Vision Server autostart sometimes fails after power cycle. | | GD | SynView-1.03.010.1090 | 2.02 | | |
Release 10/2020 - 1.04
Release 10/2020 - 1.04
Topic | Description | comment | Author | SynView Version | Petalinux Version | FPGA Version | BCRM Version |
|---|
SynView Explorer | Brightness Control - BCRM Mode / Exposure Auto Color Management -BCRM Mode / White Balance Auto
→ If "Once" is chosen, "Once" stays active. "OFF" is not active. | Issue IAM-85 | AKr | 1.03.010.1060 |
|
|
|
SynView Explorer | Events can´t be send via GigE Server | . | MW | 1.03.010.1061-8.10.2020 |
|
|
|
SynView Explorer | Timer/Puls generator can´t be enabled or disabled with Acquisition Start/Stop | . | MW | 1.03.010.1061-8.10.2020 |
|
|
|
SynView Explorer | TriggerMode: Trigger Invert operates sensor in free-run mode | | GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 |
SynView Explorer | StrobeMode: Strobe assigned to wrong edge | . | GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 |
SynView Explorer | StrobeMode: Strobe source: Static low remains high | . | GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 |
SynView Explorer | TriggerMode: Software trigger
→ Strobe not available | | GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 |
SynView Explorer | I/O
→ Line5 OUT: On -> Low, OFF → High | | GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 |
SynView Explorer | I/O:
→ Line4 OUT: No function | . | GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 |
SynView Explorer | Image Format: Pixel format:
Format Bayer GR 10 Packed cannot be displayed
Format Bayer GR 10 Packed cannot be displayed | Issue SYN-16 | GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 |
SynView Explorer | Image Format: Pixel format:
BayerRG8-frame is brighter than BGR8-frame | | GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 |
SynView Explorer | Image Format: Pixel format:
YUV-frame is brighter than BGR8-frame | Issue IAM-76 | DP | | | | |
SynView Explorer | First frame occures to "flash" | | GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 |
SynView Explorer | Soft image due to missing basic sensor configuration (gamma, black level) | | GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 |
Hardware
Topic | Description | Affects | Author |
|---|
Power supply | Power over Ethernet is not supported even though the camera will be detected as a PoE device by a PoE injector! | If the camera serial number has an X or Z in the 9th digit (e.g. 14A2GEBAX2042013) | BH |
Input and Output Interface | OUT_GP1+ is out of order and can be used in current revison. Output stays GND. This means in SynView Explorer I/O: → Line4 OUT: No function (always one!) | If the camera serial number has an X or Y in the 9th digit (e.g. 14A2GEBAX2042013) | BH |