Software
Release 01/2022 - 3.10 (2021.1)
Topic | Description | comment | SynView Version | Petalinux Version |
|---|
SynView Explorer | User Set: save does not work, when next load is done to fast. | Issue IAM-220 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | AcquisitionFrameRateTimer mode: AcquisitionFrameRate cannot be increased after increase/decrease exposure time. | Issue IAM-219 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | AcquisitionFrameRateTimer mode: acquisition stops if Exposure Auto = Continuous/Once. | Issue IAM-218 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | AcquisitionFrameRateTimer mode: Acquisition does not start after increasing exposure time. | Issue IAM-217 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | IMX265C, IMX264C: no frame output with BGR 8 format. | Issue IAM-214 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | Color Transformation: switches to OFF when aqusition is started. | Issue IAM-210 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | BGR 8 format: wrong pixels can occur when Gamma,Contrast is reduced by certain brightness. | Issue IAM-209 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | BalanceRatio(Selector) not shown as available in bayer mode. | Issue IAM-207 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | IA2312C: list of pixelformats is not correct. | Issue IAM-206 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | Trigger Modus with trigger source timer: Acquisition stops when exposure time is to high. | Issue IAM-154 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | Acquisition Frame Rate Control: exposure time controls the AcquFrameRate. | Issue IAM-149 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | Color Transformation: default-value for Color Transformation Value Selector=Offset 2 instead of Gain 00. | Issue IAM-148 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | minimal value of field "Exposure Auto Max Time" is smaler than minimal exposure time. | Issue IAM-147 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | Mono 8 is brighter as Mono10/12. | Issue IAM-142 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | Trigger Modus: acquisition stops with triggerrate in relation with too high exposure time. | Issue IAM-123 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | Acquisition Frame Rate: write failed message can occur . | Issue IAM-122 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | User Set Default "none": data will be overwritten. | Issue IAM-121 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | Digital I/O Control, Line Source "Selected Trigger" delivers no frame output. | Issue IAM-114 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | Strobe Source "Static High": behaves like "Static Low". | Issue IAM-112 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | ColorTransformation: if switched to off, it still affects the colors of the frame. | Issue IAM-165 | SynView-1.03.014.1026 | 3.10 |
SynView Explorer | IA1503, Sensor Strobe: no Frame-output with certain Exposure Time combined with Width, Height. | Issue IAM-189 | SynView-1.03.014.1026 | 3.10 |
Older Release
| Expand |
|---|
| title | Release 01/2022 - 3.01 (2021.1) |
|---|
|
Release 01/2022 - 3.01 (2021.1)Topic | Description | comment | Author | SynView Version | Petalinux Version | FPGA Version | Device Sensor Version |
|---|
SynView Explorer | Brightness Control - BCRM Mode / Exposure Auto Color Management -BCRM Mode / White Balance Auto
→ If "Once" is chosen, "Once" stays active. "OFF" is not active. | IAM-85 | AKr | SynView-1.03.010.1090 | 2.02 | | 34658 | iAMGigEServeriAMGigEServer | Events can´t be send via GigE Server | . | MW | SynView-1.03.010.1090 | 2.02 | | | SynView Explorer | Image Format: Pixel format:
YUV-frame is brighter than BGR8-frame | Issue IAM-76 | DP | SynView-1.03.010.1090 | 2.02 | | | SynView Explorer | First frame occures to "flash" | | GD | SynView-1.03.010.1090 | 2.02 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 | SynView IP Config Tool sv.ipconf.x64 | Re-enable the GigE Vision Server autostart sometimes fails after power cycle. | | GD | SynView-1.03.010.1090 | 2.02 | | |
|
| Expand |
|---|
| title | Release 06/2021 - 2.02 (2020.1). |
|---|
|
Release 06/2021 - 2.02 (2020.1)Topic | Description | comment | Author | SynView Version | Petalinux Version | FPGA Version | Device Sensor Version |
|---|
SynView Explorer | Brightness Control - BCRM Mode / Exposure Auto Color Management -BCRM Mode / White Balance Auto
→ If "Once" is chosen, "Once" stays active. "OFF" is not active. | IAM-85 | AKr | SynView-1.03.010.1090 |
2.02
|
|
34658
| iAMGigEServer | Events can´t be send via GigE Server | . | MW | SynView-1.03.010.1090 | 2.02
|
|
| SynView Explorer | Image Format: Pixel format:
YUV-frame is brighter than BGR8-frame | Issue IAM-76 | DP | SynView-1.03.010.1090 | 2.02 | | | SynView Explorer | First frame occures to "flash" | | GD | SynView-1.03.010.1090 | 2.02 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 | SynView IP Config Tool sv.ipconf.x64 | Re-enable the GigE Vision Server autostart sometimes fails after power cycle. | | GD | SynView-1.03.010.1090 | 2.02 | | |
|
| Expand |
|---|
| title | Release 10/2020 - 1.04 |
|---|
|
Release 10/2020 - 1.04Topic | Description | comment | Author | SynView Version | Petalinux Version | FPGA Version | BCRM Version |
|---|
SynView Explorer | Brightness Control - BCRM Mode / Exposure Auto Color Management -BCRM Mode / White Balance Auto
→ If "Once" is chosen, "Once" stays active. "OFF" is not active. | Issue IAM-85 | AKr | 1.03.010.1060 |
|
|
| SynView Explorer | Events can´t be send via GigE |
|
...
...
Puls generator can´t be enabled or disabled with Acquisition Start/Stop | . | MW | 1.03.010.1061-8.10.2020 |
|
|
| SynView Explorer | TriggerMode: Trigger Invert operates sensor in free-run mode | | GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 | SynView Explorer | StrobeMode: Strobe assigned to wrong edge | . | GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 | SynView Explorer | StrobeMode: Strobe source: |
|
...
Static low remains high | . | GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 | SynView Explorer | TriggerMode: Software trigger
→ Strobe not available | | GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 | SynView Explorer | I/O
→ Line5 OUT: On -> Low, OFF → High | | GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 | SynView Explorer | I/O:
→ Line4 OUT: |
|
...
No function | . | GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 | SynView Explorer | Image Format: Pixel format:
Format Bayer GR 10 Packed cannot be displayed
Format Bayer GR 10 Packed cannot be displayed | Issue SYN-16 | GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 | SynView Explorer | Image Format: Pixel format:
BayerRG8-frame is brighter than BGR8-frame |
|
...
| | GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 | SynView Explorer | Image Format: Pixel format:
YUV-frame is brighter than BGR8-frame | Issue IAM-76 | DP | | | | | SynView Explorer | First frame occures to "flash" |
|
...
Acquisition: das konnte ich sowohl bei der GigEpro (GP4206M, GP4136C) als auch bei der IAM nachvollziehen.
Daher habe ich dafür keinen Issue erfasst (so hatten wir es abgesprochen).
Ich habe stichprobenartig verschiedene Pixelformate benutzt: IAM: YUV, BGR8, Bayer GR8; 4206M:Mono 8,12; 4136C: Bayer GR8, RGB8
Was ich sehen konnte, war, dass es offensichtlich einen Zusammenhang gibt wie schnell man zwischen Start und Stop Acquisition wechselt. Läßt man z.b. einige Sekunden verstreichen nach Stop Acquisition und startet dann wieder, kommt es nicht immer zu dem „Blitzen“
| GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 | SynView Explorer | Soft image due to missing basic sensor configuration (gamma, black level) |
|
...
DP: Farben besser mit IR Filter
(siehe Emailverkehr mit Screenshots)
| GD | 1.03.010.1061-19.10.2020 | 1.04 | 0x56010102, 0x5f7db0a3 | bcrm: 0000797500000300 |
|
...
sv.ipconf.x64
...
Re-enable the GigEVisionServer autostart sometimes fails.
...
GD
...
SynView-1.03.010.1090
...
Hardware
If the camera serial number has an X in the 9th digit (e.g. 14A2GEBAX2042013) Power over Ethernet is not supported even though the camera will be detected as a PoE device by a PoE injector! |
BH | Input and Output Interface | If the camera serial number has an X or |
Y Z in the 9th digit (e.g. 14A2GEBAX2042013) | BH |
Input and Output Interface | OUT_GP1+ is out of order and can be used in current revison. Output stays GND. This means in SynView Explorer I/O: → Line4 OUT: No function (always one!) | If the camera serial number has an X or Y in the 9th digit (e.g. 14A2GEBAX2042013) | BH |
