| Excerpt |
|---|
...
...
Change IP System Settings of iam
| Include Page | ||||
|---|---|---|---|---|
|
...
Configuring the Network Controller
The configuration of your network controller depends on your operating system (OS).
In case of using a virtual guest system
...
configure only
...
the host network controller!
| Note |
|---|
...
Improve the network performance |
...
considerably by configuring the network controller properly. |
Connecting to the Camera
The camera is designed to be remotely controlled over OpenSSH.
After power up it will take some time before the camera will respond due to the booting of the Linux system.
Configure the network controller properly as described below before using the ping command.
The ping terminal command can be applied to see if the camera has booted:
...
| Info |
|---|
In abscence of a Linux or Mac host system NET provides a virtual machine image. How to set up the virtual machine is described in section Application Development / Virtual Host System below. See also section Communicate with iam over windows host - without the virtual machine. |
IP Address Settings
Mac / Linux
| Info |
|---|
Under Linux and Mac |
...
the same physical |
...
network controller with |
...
multiple virtual controller settings |
...
is applicable. Therefore it is not |
...
necessary to change |
...
the current network setting |
...
. Instead, just add a new virtual controller |
...
. |
...
Windows 10
Open the
...
Windows10 start menu by pressing the
...
Windows key on
...
the keyboard.
...
Type the words
Control Paneland press enter.Click the link titled
View network status and tasksunder theNetwork and Internetheading.Click the link on the left of the window labeled
Change adapter settings.Right click on
...
network adapter and choose
propertiesto open
...
the properties window.
Find the option of
Internet Protocol Version 4 (TCP/IPv4)and click on it. Then choose
...
option
...
Properties, e.g. as shown below.
...
...
Test the connection
...
with the ping command
...
first on
...
the host system and
...
than inside the virtual machine if using a virtual guest system
...
.
Configure
...
the Network Controller Settings
Jumbo frames
| Info |
|---|
Jumbo frames are Ethernet frames with more than 1500 bytes of payload, the limit set by the IEEE 802.3 standard. In particular |
...
, GigE Vision jumbo frames can improve network performance |
...
massively since image data |
...
is originally high-volume data. |
...
Windows: Activating jumbo frames
...
Follow steps 1 to 4
...
in the section above.
...
property window: Click onConfigure.
...
Select the second tab
Advancedin the new window
...
.
Look for the
...
property
Jumbo PacketsSelect the highest value,
...
e.g.
9014 Bytes
Confirm with
OK
Connecto to Camera
The Camera is designed to be remote controlled over Openssh.
After power up it will take some time while the linux system is booting before the camera will respons.
On can use the ping terminal comand to see if the camera has booted:
...
| Info |
|---|
If you do not have a linux or mac host system available NET provides a virtual machine image. How to set up the virtual machine is described in section Application Development / Virtual Host System below. You also can follow the steps of section Communicate with iam over windows host - without the virtual machine. |
🔍 References
Interrupt Moderation
| Info |
|---|
Interrupt Moderation is a feature that groups packets together and sends them as a batch. It can be responsible for sluggish behavior of the connection. For a continuous image data transmission this feature is not very useful. |
Windows: Disable Interrupt Moderation
For disable this feature follow the Steps 1. to 4. from the section above.
From the
property windowclick onConfigureSelect the second tab from the new window
AdvancedLook for the property
Interrupt ModerationSelect the
Disable
Other features and options
Helpful content: Blogpost about Optimizing Ethernet Adapter Settings for Maximum Performance (external link).
...
🔗 related content
...
👥 contact NET
...