Excerpt

Table of Contents

Software

Release 01/2022 - 3.10 (2021.1)

Topic	Description	comment	SynView Version	Petalinux Version
SynView Explorer	User Set: save does not work, when next load is done to fast.	Issue IAM-220	SynView-1.03.014.1026	3.10
SynView Explorer	AcquisitionFrameRateTimer mode: AcquisitionFrameRate cannot be increased after increase/decrease exposure time.	Issue IAM-219	SynView-1.03.014.1026	3.10
SynView Explorer	AcquisitionFrameRateTimer mode: acquisition stops if Exposure Auto = Continuous/Once.	Issue IAM-218	SynView-1.03.014.1026	3.10
SynView Explorer	AcquisitionFrameRateTimer mode: Acquisition does not start after increasing exposure time.	Issue IAM-217	SynView-1.03.014.1026	3.10
SynView Explorer	IMX265C, IMX264C: no frame output with BGR 8 format.	Issue IAM-214	SynView-1.03.014.1026	3.10
SynView Explorer	Color Transformation: switches to OFF when aqusition is started.	Issue IAM-210	SynView-1.03.014.1026	3.10
SynView Explorer	BGR 8 format: wrong pixels can occur when Gamma,Contrast is reduced by certain brightness.	Issue IAM-209	SynView-1.03.014.1026	3.10
SynView Explorer	BalanceRatio(Selector) not shown as available in bayer mode.	Issue IAM-207	SynView-1.03.014.1026	3.10
SynView Explorer	IA2312C: list of pixelformats is not correct.	Issue IAM-206	SynView-1.03.014.1026	3.10
SynView Explorer	Trigger Modus with trigger source timer: Acquisition stops when exposure time is to high.	Issue IAM-154	SynView-1.03.014.1026	3.10
SynView Explorer	Acquisition Frame Rate Control: exposure time controls the AcquFrameRate.	Issue IAM-149	SynView-1.03.014.1026	3.10
SynView Explorer	Color Transformation: default-value for Color Transformation Value Selector=Offset 2 instead of Gain 00.	Issue IAM-148	SynView-1.03.014.1026	3.10
SynView Explorer	minimal value of field "Exposure Auto Max Time" is smaler than minimal exposure time.	Issue IAM-147	SynView-1.03.014.1026	3.10
SynView Explorer	Mono 8 is brighter as Mono10/12.	Issue IAM-142	SynView-1.03.014.1026	3.10
SynView Explorer	Trigger Modus: acquisition stops with triggerrate in relation with too high exposure time.	Issue IAM-123	SynView-1.03.014.1026	3.10
SynView Explorer	Acquisition Frame Rate: write failed message can occur .	Issue IAM-122	SynView-1.03.014.1026	3.10
SynView Explorer	User Set Default "none": data will be overwritten.	Issue IAM-121	SynView-1.03.014.1026	3.10
SynView Explorer	Digital I/O Control, Line Source "Selected Trigger" delivers no frame output.	Issue IAM-114	SynView-1.03.014.1026	3.10
SynView Explorer	Strobe Source "Static High": behaves like "Static Low".	Issue IAM-112	SynView-1.03.014.1026	3.10
SynView Explorer	ColorTransformation: if switched to off, it still affects the colors of the frame.	Issue IAM-165	SynView-1.03.014.1026	3.10
SynView Explorer	IA1503, Sensor Strobe: no Frame-output with certain Exposure Time combined with Width, Height.	Issue IAM-189	SynView-1.03.014.1026	3.10

Older Release

Expand

title	Release 01/2022 - 3.01 (2021.1)

Release 01/2022 - 3.01 (2021.1)

Topic	Description	comment	Author	SynView Version	Petalinux Version	FPGA Version	Device Sensor Version
SynView Explorer	Brightness Control - BCRM Mode / Exposure Auto Color Management -BCRM Mode / White Balance Auto → If "Once" is chosen, "Once" stays active. "OFF" is not active.	IAM-85	AKr	SynView-1.03.010.1090	2.02		34658
iAMGigEServeriAMGigEServer	Events can´t be send via GigE Server	.	MW	SynView-1.03.010.1090	2.02
SynView Explorer	Image Format: Pixel format: YUV-frame is brighter than BGR8-frame	Issue IAM-76	DP	SynView-1.03.010.1090	2.02
SynView Explorer	First frame occures to "flash"		GD	SynView-1.03.010.1090	2.02	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView IP Config Tool sv.ipconf.x64	Re-enable the GigE Vision Server autostart sometimes fails after power cycle.		GD	SynView-1.03.010.1090	2.02

Expand

title	Release 06/2021 - 2.02 (2020.1).

Release 06/2021 - 2.02 (2020.1)

Topic

Description

comment

Author

SynView Version

Petalinux Version

FPGA Version

Device Sensor Version

SynView Explorer

Brightness Control - BCRM Mode / Exposure Auto

Color Management -BCRM Mode / White Balance Auto
→ If "Once" is chosen, "Once" stays active. "OFF" is not active.

IAM-85

AKr

SynView-1.03.010.1090

2.02

34658

iAMGigEServer

Events can´t be send via GigE

...

Server	.	MW	SynView-1.03.010.1090	2.02
SynView Explorer	Image Format: Pixel format: YUV-frame is brighter than BGR8-frame	Issue IAM-76	DP	SynView-1.03.010.1090	2.02
SynView Explorer	First frame occures to "flash"		GD	SynView-1.03.010.1090	2.02	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView IP Config Tool sv.ipconf.x64	Re-enable the

...

GigE Vision Server autostart sometimes fails after power cycle.

GD

SynView-1.03.010.1090

2.02

Expand

title	Release 10/2020 - 1.04

Release 10/2020 - 1.04

Topic

Description

comment

Author

SynView Version

Petalinux Version

FPGA Version

BCRM Version

SynView Explorer

Brightness Control - BCRM Mode / Exposure Auto

Color Management -BCRM Mode / White Balance Auto
→ If "Once" is chosen, "Once" stays active. "OFF" is not active.

Issue IAM-85

AKr

1.03.010.1060

SynView Explorer

Events can´t be send via GigE

...

Server	.	MW	1.03.010.1061-8.10.2020
SynView Explorer	Timer/

...

Puls generator can´t be enabled or disabled with Acquisition Start/Stop	.	MW	1.03.010.1061-8.10.2020
SynView Explorer	TriggerMode: Trigger Invert operates sensor in free-run mode		GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView Explorer	StrobeMode: Strobe assigned to wrong edge	.	GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView Explorer	StrobeMode: Strobe source:

...

Static low remains high	.	GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView Explorer	TriggerMode: Software trigger → Strobe not available		GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView Explorer	I/O → Line5 OUT: On -> Low, OFF → High		GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView Explorer	I/O: → Line4 OUT:

...

No function	.	GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView Explorer	Image Format: Pixel format: Format Bayer GR 10 Packed cannot be displayed Format Bayer GR 10 Packed cannot be displayed	Issue SYN-16	GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView Explorer	Image Format: Pixel format: BayerRG8-frame is brighter than BGR8-frame		GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView Explorer	Image Format: Pixel format: YUV-frame is brighter than BGR8-frame	Issue IAM-76	DP
SynView Explorer	First frame occures to "flash"		GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300
SynView Explorer	Soft image due to missing basic sensor configuration (gamma, black level)		GD	1.03.010.1061-19.10.2020	1.04	0x56010102, 0x5f7db0a3	bcrm: 0000797500000300

...

SynView IP Config Tool

sv.ipconf.x64

...

GD

...

SynView-1.03.010.1090

...

2.02

Hardware

Topic	Description	Affects	Author
Power supply

If the camera serial number has an X in the 9th digit (e.g. 14A2GEBAX2042013)

Power over Ethernet is not supported even though the camera will be detected as a PoE device by a PoE injector!

BH

Input and Output Interface

If the camera serial number has an X or

Y

Z in the 9th digit (e.g. 14A2GEBAX2042013)	BH
Input and Output Interface	OUT_GP1+ is out of order and can be used in current revison. Output stays GND.

BH

This means in

SynView Explorer

I/O:

→ Line4 OUT:

no

No function (always one!)

.

GD

1.03.010.1061-19.10.2020

1.04

0x56010102, 0x5f7db0a3

bcrm: 0000797500000300

If the camera serial number has an X or Y in the 9th digit (e.g. 14A2GEBAX2042013)

BH

Versions Compared

Old Version 11

New Version Current

Key

Software

Release 01/2022 - 3.10 (2021.1)

Older Release

Release 01/2022 - 3.01 (2021.1)

Release 06/2021 - 2.02 (2020.1)

Release 10/2020 - 1.04

Hardware

Page Comparison

Versions Compared

Old Version 11

New Version Current

Key

Software

Release 01/2022 - 3.10 (2021.1)

Older Release

Release 01/2022 - 3.01 (2021.1)

Release 06/2021 - 2.02 (2020.1)

Release 10/2020 - 1.04

Hardware