...
...
...
...
...
...
...
...
...
...
...
...
...
...
| Excerpt |
|---|
Connector and cable description
Ethernet connector
...
 | All the grounds from individual connectors are connected inside the camera. |
I/O Connector and Pinout
17-pin male M12 connector for digital i/o (optocoupler and TTL inputs/outputs) and power input.
CORSIGHT I/O connector |
|---|
...
CORSIGHT I/O adapter cable, D-sub 25-pin connector |
|---|
...
view manufactor information (external link)
...
 |  |
Pinout (including pin numbers on the D-sub-25 adapter cable)
If the camera serial number has an X or Y in the 9th digit (e.g. 14A2GEBAX2042013) the I/O connector has the Prototype pinout!
Pin # |
|---|
...
Signal | D-Sub 25 | |
|---|---|---|
1 |
...
Power In- | 12 | |
2 |
...
Power In+ | 19 | |
3 |
...
Optocoupler Input 3 Anode | 7 | |
4 |
...
Ground | 5 | |
5 |
...
IN_ENC1+
Optocoupler Output 1-3 Collector | 10 |
6 |
...
IN_ENC2+
Optocoupler Output 0 Emitter | 9 |
7 |
...
IN_ENC3+
Optocoupler Output 1 Emitter | 11 |
8 |
...
Optocoupler Output 3 Emitter | 24 | |
9 |
...
OUT_GP1+
TTL Input | 21 |
10 |
...
TTL Output | 20 | |
11 |
...
Optocoupler Input 2 Anode | 6 | |
12 |
...
Optocoupler Input 0 Cathode | 2 | |
13 |
...
Optocoupler Input 0 Anode | 1 | |
14 |
...
SGND_IO
Optocoupler Output 0 Collector | 8 | |
15 | Optocoupler Output 2 Emitter | 25 |
16 | Optocoupler 1 Input Anode | 3 |
17 | Optocoupler 1-3 Input Cathode | 4 |
Pins 13, 14, 15, 16, 17, 18, 22, 23 on the D-sub 25 connector are not connected.
Cable Assembly
| Info |
|---|
An adapter cable is available (see Section “Accessories”), with D-sub 25-pin female interface connector. The table below lists the pinouts also for the connectors of the adapter cable. This cable is fully shielded. |
|
PC system connector
24-pin female M16 connector for DP++, RS232 and USB 2.0.
CORSIGHT PC System connector
An adapter cable are available (see Section “Accessories”), separating individual signal groups into three dedicated connectors: DP++ male, USB Type A female, and RS232 (D-sub 9-pin male). The table below lists the pinouts also for the connectors of the adapter cable.
CORSIGHT PC system adapter cable, DP++ connector
CORSIGHT PC system adapter cable, USB connector
CORSIGHT PC system adapter cable, D-sub 9-pin connectors (RS-232)
Pinout (including pin numbers on the DP++/USB/RS232 adapter cable)
M16 | Signal | DP | USB | RS-232 |
|---|---|---|---|---|
1 | ML0+ | 12 | - | - |
2 | ML3- | 1 | - | - |
3 | ML2+ | 6 | - | - |
4 | ML2- | 4 | - | - |
5 | ML3+ | 3 | - | - |
6 | ML0- | 10 | - | - |
7 | ML1+ | 9 | - | - |
8 | ML1- | 7 | - | - |
9 | AUX- | 17 | - | - |
10 | GND | 2, 5, 8, 11, 16 | - | - |
11 | Hot Plug | 18 | - | - |
12 | +5V | - | - | - |
13 | +5V | - | - | - |
14 | GND | - | 4 | - |
15 | GND | - | - | - |
16 | AUX+ | 15 | - | - |
17 | USB- | - | 2 | - |
18 | +5V USB | - | 1 | - |
19 | GND | - | - | 5 |
20 | RS232_TX | - | - | 3 |
21 | CONF1 | 13 | - | - |
22 | RS232_RX | - | - | 2 |
23 | +5V USB | - | - | - |
24 | USB+ | - | 3 | - |
- | Shield | - | - | - |
Pins 14, 19, 20 on the DP connector are not connected.
Pins 1, 4, 6, 7, 8, 9 on the RS232 D-sub 9 connector are not connected.
The cable carries following signals via twisted pair wires: ML0+/ML01, ML1+/ML1-, ML2+/ML2-, ML3+/ML3-, AUX+/AUX-, USB-/USB+.
All grounds are connected together.
Ethernet connector
8-pin female M12 Ethernet connector.
CORSIGHT Ethernet connector
An adapter cable is available (see Section “Accessories”), with standard Ethernet connector, 8P8C modular plug, often also referred to as RJ-45.
Ethernet RJ-45 connector
CORSIGHT Ethernet connector, pinout
Pin | Signal (1000BASE-T) | Signal (10BASE-T, 100BASE_TX) | Pin RJ-45 |
1 | BI_DC- | NC | 5 |
2 | BI_DD+ | NC | 7 |
3 | BI_DD- | NC | 8 |
4 | BI_DA- | TX- | 2 |
5 | BI_DB+ | RX+ | 3 |
6 | BI_DA+ | TX+ | 1 |
7 | BI_DC+ | NC | 4 |
8 | BI_DB- | RX- | 6 |
Status LED
The CORSIGHT cameras are equipped with a set of status LED's. The positions of the LED's on camera's side is shown on the figure below. The purpose of the individual LED's (starting from connector side) is:
WLAN activity (blue)
User LED (green, software programmable)
Ethernet speed (green, still for 1GB, blinking for 100Mb Ethernet)
Ethernet link (orange)
Power (green)
SATA activity (orange)